Təsvir
The line specially designed for our russian customer who sent to us the glass bottles (thin&tall) is suitable for food packing industry like olive oil/wine bottles fill-cap-label process.
Samples offered by our EU customer
The whole line including filling capping labeling machine
1.model NPACK-5030 piston filling machine
2.model NPACK-AC40 ROPP capping machine
3.model NPACK-650A double sided labeling machine
4.Nitrogen gas flushing function after filling
5.Accumulation turntable for collecting final product
As below there is the basic description &introduction one by one :
►Model NPACK-5030 four heads piston filling machine
Mikrokompüter tərəfindən idarə olunan 4heads zeytun doldurma maşını fotoelektrikliyi pnevmatik əməliyyatla birləşdirir,
thus widely is applied for the liquid filling of the agriculture chemical、solution、liquid detergent、cosmetic as well as olive.The filling volume is precise,foamless and stable.
The machine can fill the liquid with the range from 25-1000ml,meanwhile there is no special requirement on the shapes of bottles.That is to say,it can fill the liquid for the normal bottles as well as the irregular-shaped bottles.
Model NPACK-5030
Filling range 50~3000ml
Filling speed <20-30b/m(for 500-1000ml liquid)
Dəqiqlik ± 1%
Güc / təchizat gücü 0.8kw 、 220v
İş təzyiqi 5 ~ 6kq / sm3
Air consumption 0.5-0.7mpa
NW 500kg
Outer dimension 2000×800×1900mm
Mark:The filling nozzles can be designed and manufactured according to requirements from customers on the filling range and filling speed
Filling speed adjustment
Filling speed adjustment has the following 6 factors:
1, the speed of the product is determined by the viscosity of the product and the length of the suction pipe.
2, filling speed depends on the diameter of the filling head, the diameter is large, the speed is quick.
3, the product of the bubble level. The product filling speed of the high bubble should be slowed down.
4, how much is the filling quantity.
5, the accuracy of the filling quantity, adjust the filling time of each cast.
6, adjust the filling speed (that is, the speed of the servo motor).
General trouble shooting and processing
1)Touch screen is not shown, but the indicator light
Fault cause:
Check whether the fuse is burning, or the contact is bad, replace or reinstall the fuse.
2)The output indicator of the programmable controller has an output indicator, but the solenoid valve does not work.
Fault cause:
Upon examination of the solenoid valve failure, is the key to the programmable controller in the electrical damage, can replace the same type of intermediate relay, fault can be ruled out (this fault is very rare).
3)The main head there is a leak in the shutdown.
Fault cause:
The filling head cylinder does not move up and down, replaced PTFE head, check on the stingy joints have gas, or replace the filling valve, can be ruled out
4)After filling in a number of bottles do not fill
Fault cause:
♦Check whether the bottle counting electric eye, if not counting adjustable electric distance, so that it can reach the count;
♦ Check that the liquid level indicator is black, if it is white, and the liquid level is fluid, and can be filled with black
♦ Check the magnetic switch cylinder after the dive, the light is bright, if not bright, adjust to the light.
♦Check the back of the servo motor is close to the switch is bright, if not bright, adjust to the light.
5)Individual valve or cylinder action to slow down or do not work.
Fault cause:
♦The general situation is caused by the fault of the control valve, first check to control the output of the output of the display lamp (in the lower left of the programmable controller) work is normal, confirm the normal operation of the following check.
♦Magnet coil plug for transposition of the solenoid valve, if change the position of the fault, indicating that the electromagnet coil is damaged, replace the coil after failure can be ruled out.
If the valve group of the emptying port does not stop to have a lot of gas, the system has a more serious leakage. Can check the internal sealing condition, if damaged, should be replaced. If the fault can not be ruled out, can check the valve spool movement, see if there is a card phenomenon or the seal is damaged, and repair, if damaged more serious, it should be replaced by the entire valve.
6)Servo motor alarm.
Fault cause:
♦Check whether the PLC on the F**, if it is to turn off the power, and then open up to manual operation, a number of seconds after the manual injection, and then press the manual back to zero.
►Nitrogen gas flushing system
NPACK-AC40 Automatic ROPP capping machine for olive bottle with metal caps with protective chamber
düyməni idarəetmə sistemi olan avtomatik ROPP örtmə maşını
ROPP qapağı üçün başları vurmaq
Örtmə maşını plastik şüşə bottle ev şüşəsi Al üçün alüminium qapaqları və şüşə butulkanın rulon presini möhürləməsi üçün əlverişli bir cihazdır. Bu vintlə preslənən vintlə preslənən qablardakı yuvanın altındakı şüşə üçün avtomatik bəslənən şüşə. 、 Qapaqlar, tərs qapaqları çıxardaraq .Qapalı şüşə sabit örtmə effekti, rahat açılmamaq kimi xüsusiyyətlərə üstünlük verir ki, bu da gizli və oğurluğa qarşı fəaliyyət göstərir.
Model NPACK-AC40
Təchizat tozu (V / Hz) AC 220/50 380/60
Tutum (m / dəq) ≧ 4000B / M
Qapaq ölçüsü (mm) 250-1000
Tətbiq Alum-qapaqlar
Vakuum pumundan hava egzozu (m3 / s) 5KG
Xarici ölçü (L × W × H) (mm) 2000 × 1000 × 2300
NG (kq) 520
ROPP örtmə iş prosesinin çəkilməsi (konveyer platforması ilə avtomatik xətt kimi nümunə götürmək)
How to operate model NPACK-C25 Single head ROPP capping machine
Konveyer kəmərində hərəkət edən yem konteyneri, qidalanma qurdu vasitəsilə yem ulduz təkərinə verilir, ulduz çarxı sonrakı indeksləmə hissəsindəki mühürləmə başının altına konteyner gətirir, yəni şüşə qapağın doldurulma yerindən qapağı götürür. qabın gövdəsi və boynu fırlanan başın altına yerləşdirildiyi, sızdırmazlıq başının iplik və sızdırmazlıq mükəmməl işləməsi.
Görkəmli Xüsusiyyətlər:
Bölmə kompakt və çox yönlüdür.
SS Slat konveyer
SS Elegantly Matt Tamamlanmış Bədən
Ön idarəetmə panelində quraşdırılmışdır
Vibratör Bowl
A / c Tezlik Sürücü ilə
►model NPACK-650A double sided labeling machine
The labeling equipment is for the round bottle labeling in the industry like food、oil、pharma、wine、cosmetics and so on.
The machine with elegant design can be easily operated and maintained by the common worker,
who requires no special training in operation this machine.Just give a simple adjustment to produce another product when you want to swap the different kinds bottle labeling.
Metal caps capping+labeling line
The bottle labeler is thus out from as below-mentioned characteristics:
1: Avadanlıqların əsas korpusu SUS304 və inkişaf etmiş Alüminium məhsullarından hazırlanmışdır.
2:The labeling heads is driven by the stepping motor that is imported from Japan.
3: Bütün işıq sensoru avadanlıqları həm Yaponiyadan, həm də Almaniyadan gətirilir
4: PLC 60 yaddaş vahidi ilə insan-maşın interfeysi ilə idarə olunur
5: Maşın tək işçinin işləməsi üçün ən yaxşı seçimdir.
6: Maşın şüşə düzəldici, şüşə paylayan 、 etiketləmə 、 sıçrayış və sayma kimi funksiyaya malikdir.
7: mövqe 、 boyu label etiketləmə bucağı asanlıqla tənzimlənə bilər.
8: Konveyer kəməri ilə təchiz olunmuş maşın, istehsal xəttinin dəstinə tətbiq olunur.
Basic parameter of double sides labeling machine
Gərginlik | 220V, 50HZ |
Güc | 2KW |
Labeling Speed | 20-120bottles/min, 150-200bottle/min |
Labeling Accuracy | ± 1 mm |
Printer to use air | 5 kg/cm2 |
Object Size | 30-200 mm(H),30-100 mm(W) |
Label Size | 25-300 mm(L),20-180 mm(W) |
Roll Size | 76 mm(Inside),380 mm(Outside) |
Ölçü | 3048(L)×1500(W)×1600(H) mm |
turntable for accumulation of final product